Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Garland
Garland gate repair usually costs between $145 and $780 depending on whether you need a hinge and post reset, a board-level opener fix, or full weld work on a rusted frame. Most repairs on this side of Garland are done in one visit, and you’ll get a written price before a single bolt is turned. Ironworks Gate Co. knows the homes here, from Firewheel to Duck Creek, and our crews are on call for Garland residents at (936) 277-6521. We’ve been fixing driveway gates for over 42 years, and this city’s gates have their own particular set of problems. We’ll walk you through them plainly.
Why Ironworks Gate Co. Is Garland’s Preferred Gate Repair Company
Our name in Garland has been built the slow way, one gate at a time. Homeowners here tend to own their houses for decades, and they’ve usually had at least one contractor treat them poorly. We hear it often on first calls off Belt Line Road and Naaman School Road. So we don’t do rushed work, and we don’t leave a job until the gate runs the way it should. It’s the only way to work in a city this big that still feels like small neighborhoods.
Victor Salinas leads our crew, and he’s held the standard since day one: square deal, upfront price, a gate that stays fixed. We’re background-checked and uniformed on every property, and the same team that answers the phone is the one that schedules and dispatches. We also carry the parts Garland gates actually need, not just the generic stuff shipped from out of state. Being local means showing up with a LiftMaster control board or a FAAC limit switch already in the truck.
When a gate is stuck open on a June afternoon, or a slide gate refuses to close before a storm, the response time matters. Garland homeowners call, and a live person answers. Twenty-four hours a day. Not a voicemail tree. That’s not marketing; it’s how we run a gate company.
Our Gate Repair Services in Garland
Electric Gate Repair
Electric gate repair in Garland typically runs $180 to $420 for logic board, limit switch, or relay work on most residential operators. We test the motor, then the controls, then the safety loop. On older Garland homes near Duck Creek and Springpark, we find the operator is still fine and the bird’s nest of low-voltage wiring has corroded through at a splice from the last handyman job. We replace the run, re-sleeve it, and leave the box clean enough to read.
Automatic Gate Repair
Automatic gate repair in Garland often comes down to an operator that was installed wrong from the start, not one that simply wore out. The rack on a slide gate slipped, or the arm travel wasn’t set, so the board has been cycling against a bind for two years. A typical board replacement runs $220 to $590 depending on the brand. The operator: at least twice that. We diagnose before we quote, so you don’t pay operator money for a switch problem.
Hinge & Post Repair
This is the quiet majority of our work in Garland. The soil here is heavy clay. It swells when wet and cracks when dry. A hinge post set in a shallow 18-inch footing will be out of plumb within a handful of seasons. Hinge and post repair in Garland usually runs $250 to $650 depending on whether we’re cutting out and re-setting one post or two. We pull the post, dig a deeper footing, set it with rebar, and then re-hang the panel so it clears evenly. This is the fix that keeps a gate from being repaired twice a year.
Gate Realignment
A gate that’s dragging on the driveway or latching on only one corner is rarely just sag in the panel. After years of Garland’s wet-dry cycles, the post has moved, even if it looks straight from the curb. Realignment runs $160 to $380 in Garland when the structure is sound and only the hardware needs attention. We measure it, shim it, re-hang it, and then run the opener through its full travel and safety checks. A gate that closes smoothly on the first try is the whole point.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Garland
We’re factory-trained on nine automation lines, so we don’t have to guess when a Garland customer calls about their opener. LiftMaster, FAAC, BFT, and Linear are the ones we see most often on this side of town. We keep control boards, limit switches, and remote receivers for those brands in our service vehicles, which means many Garland calls are done on the first trip. If your gate system uses something else, we’ll tell you honestly whether the fix makes sense or whether the opener has reached the age where a replacement is cheaper than another repair.
Common Gate Repair Problems We See in Garland Homes
- Hinge posts leaning out of plumb. Garland’s clay soil expands and contracts every season. Shallow footings pivot, the gate starts dragging, and the safety photocell gets thrown off. Most of our realignments here start at the post, not the hinge.
- Operators burning out against a shifted post. When the rack and pinion bind, the motor pulls more current and the board or contactor fails. The motor itself is often fine. We see this on slide gates all down George Bush Turnpike.
- Loop detectors failing intermittently. Near Garland’s high-voltage utility corridors, induction loops under the driveway can false-trigger or ignore a command. The gate stops mid-travel. We replace or re-tune the detector and check for a clean frequency.
- 1990s-era gate hardware reaching the end of its life. Much of Garland’s housing stock went in during the 80s and 90s, and a lot of these gates are original. Weld joints crack, pickets rust through at the bottom rail, and the operator is old enough to vote. We’ll tell you straight what can be saved and what can’t.
Pricing for Gate Repair in Garland, TX
Here’s what Garland homeowners can expect to pay. A basic service call with diagnostic time starts at $89. Hinge replacement on a single swing panel: $145 to $260. Hinge post reset with new concrete footing: $300 to $650. Weld and rust repair on a steel gate frame: $180 to $500 depending on the number of joints and the amount of grinding. Operator board replacement: $220 to $590 depending on brand. Full slide gate rack replacement: $340 to $720. These are the numbers we quote, in writing, before work begins. The price you agree to is the price on the invoice. No add-on charges after the fact.
We also run standing offers for Garland customers: $50 off any repair over $250, a free second opinion on any written estimate, and an $89 seasonal tune-up. Seniors and veterans always get 5 percent off. Call (936) 277-6521 and we’ll give you a real number, not a range.
We Also Serve Cities Near Garland
Our crews work throughout Garland and the surrounding communities. If you’re in Richardson, Mesquite, Addison, or Dallas, the same Gate Repair team covers your neighborhood. We dispatch from our Dallas-Fort Worth office and keep our routes around the northeast suburbs tight, so we can usually get to you the same week.
Serving Garland, TX - Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Garland
The clay soil under Garland’s swing gates expands and contracts with the seasons, so the hinge post shifts out of plumb even if every bolt is tight. The post itself has moved. Dug-out footings and heavy frost are the cause, and the only permanent fix is re-setting the post in a deeper concrete footing. Tightening hinges against a leaning post just strips the threads.
We fixed a gate just like this on Shiloh Road. The LiftMaster swing gate was scraping the driveway every spring. Our tech found the hinge post leaning 9 degrees out from years of clay expansion; instead of just re-hanging the panel, we pulled the post, poured a new 24-inch footing with rebar, and then did a full sag correction on the gate. The operator’s safety photocell was misaligned from the shift too, so we re-aimed it and ran three full UL 325 reversal tests before we left.
No. Most sagging slide gates in Garland are repaired by re-aligning the track, adjusting the rollers, or re-welding the gate frame, not by tearing up the driveway. We only dig when the problem turns out to be a broken post or a foundation issue underneath the track. You’ll know before any concrete gets cut, because we walk the job with you first.
The first thing to check is whether a safety edge or photocell has become misaligned, which happens often when a Garland post shifts and moves the sensor heads. The beep-and-reverse means the board thinks something is in the path. In our experience on Garland properties, the cause is usually a bent mounting bracket that no longer lines up with the reflector, not the motor. Call us and we’ll re-aim or replace the sensors and run a full reversal test.
Yes, a solar opener can work on an existing gate in Garland, provided the panel gets decent south-facing sun and the gate isn’t deeply shadowed by trees or a porch. You’ll still need a battery bank and a properly sized panel. Garland’s summer heat is rough on batteries, so we size the panel to handle both the operator and the trickle charge, not just the motor draw. We’ll tell you if solar is actually worth it for your specific gate, or if a hardwired run is cheaper and more reliable long-term.
For Garland’s clay, we recommend at least 24 inches of depth below the frost line, with a footing at least 18 inches across and rebar reinforcement. Anything less than 24 inches will move within a few wet-dry cycles, and you’ll be calling us every spring for the same drag. The county building code has minimums, but we build deeper than the minimum, because we’ve dug up enough shallow footings in Garland to know what fails.
If your gate is dragging, beeping, or dead in the driveway, call (936) 277-6521. We’ll give you an honest diagnosis and a written price before any work starts. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Garland and the northeast Dallas suburbs.