Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Installation for Highland Park Homeowners
A new driveway gate in Highland Park typically costs between $4,800 and $14,000 installed, depending on the material, length, and whether you’re adding automation. Most installations take two to four days from first measure to final walkthrough, and we quote the full price in writing before any work begins. When a gate sags, scrapes the driveway, or simply doesn’t match the house it fronts, the right Best Gate Installation in Highland Park, TX fixes it for decades, not seasons. Since 1984, Ironworks Gate Co. has built and hung gates across Highland Park, University Park, and the surrounding neighborhoods, and we’ve been led by Victor Salinas for the better part of that run. We’re the gate specialist homeowners call when they want the job done once, correctly, and guaranteed. Call (936) 277-6521 to schedule a free measure and written estimate.
What Our Gate Installation Service Includes
Every gate installation we take on starts with the site itself: the driveway’s slope, the soil, the existing posts or lack of them, and the way the gate will actually swing or slide through a Highland Park yard. We build for the specific conditions of your property, not a catalog photo. Below is what each type of installation involves.
Driveway Gate Installation
A driveway gate is the workhorse of the property: it opens and closes more times in a year than most gates do in five, and it has to hold up to Texas wind, rain, and the occasional delivery truck backing into it. We install driveway gates in steel, wrought iron, aluminum, and wood, sized to the actual width of your drive and hung on posts set deep enough for Highland Park’s clay soil. Automation is optional at install, but we always plan the post locations and gate weight around it so adding a motor later doesn’t require redoing the job.
Pedestrian Gate Installation
A pedestrian gate gives you a separate, lighter entry alongside the driveway for foot traffic without opening the whole drive every time someone walks up. We build these to match the main gate’s style and finish, with self-closing hinges and a latch that meets the same standard as the driveway gate. In Highland Park, where many side yards slope toward the alley, we set pedestrian gates with a slight clearance gap so they never bind against the path in wet weather.
Sliding Gate Installation
A sliding gate is the right answer for driveways with a steep grade, a short setback, or a curve where a swing gate would clip a car or a wall. The gate travels on a track and rollers, which means the weight sits on the ground rather than hanging off a hinge post. We install cantilever and V-track sliding systems, set the concrete pad or posts level, and dial in the travel stops so the gate opens fully without slamming into the end catch.
Swing Gate Installation
Swing gates are the classic Highland Park look: two leaves that part in the middle, or a single leaf that sweeps across the drive. The posts carry the entire load, which is why we size and set them deeper than code minimums and weld the hinge tabs in place rather than bolting them as an afterthought. Before we hang the leaf, we check the swing arc for obstructions, including cars parked on the apron and any landscaping that might grow into the path over a decade.
Double Gate Installation
A double gate splits the driveway opening into two leaves, which cuts the swing arc roughly in half and puts less strain on each hinge post. That matters on wider driveways in Highland Park where a single leaf would sag under its own weight inside a few years. We set a cane bolt or drop rod on the inactive leaf so it stays put when closed, and we align the two leaves to meet cleanly at the center without a gap or a fight over the latch.
Security Gate Installation
A security gate is built to slow someone down: heavier gauge tubing, closer picket spacing, a taller panel, and hardware that can’t be lifted off its hinges with a pry bar. We weld the pickets to the frame rather than mechanically fastening them, and we offer steel frames with pickup-proof hinges and latch guards. If access control is part of the job, we run the conduit and wire during installation so the keypad, intercom, or vehicle detector mounts cleanly instead of looking like an afterthought.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Installation
We’re trained and equipped on nine gate-automation brands, and when a Highland Park homeowner already has a motor on the property or wants a specific opener paired with the new gate, we install to match. For LiftMaster, we’re familiar with the full residential lineup from the LA400 up through the heavy-duty swing and slide units, and we stock the common control boards and limit switches to keep installs moving the same week. On BFT gear, we’ve handled enough of the Italian-built rams to know their mounting geometry cold, which means a BFT piston on a new steel gate gets positioned so the travel stays smooth through the full arc.
Linear and Viking are two brands we see often on older Highland Park estates, and we’re set up to either integrate the existing opener with a new gate or install a fresh Linear or Viking actuator sized to the new leaf’s weight. Ghost Controls is a popular retrofit on lighter driveway and pedestrian gates, and we install their kits with the same care we’d give a commercial opener: correct wire gauge, weatherproofed connections, and a clean tie-in to the control board. Whether you have one of those four or any other make on the driveway, the installation gets planned around the opener so nothing has to be reworked later.
Signs You Need Gate Installation Right Now
- The gate scrapes the driveway or won’t close past the halfway point. That’s almost always a structural problem: post lean, hinge wear, or a leaf that’s deformed under its own weight. You can shim and patch for a while, but a gate that drags is telling you the geometry is gone, and the fix is a properly built replacement.
- The posts wobble when you push on the leaf. A gate post that moves means the footing has failed or was never deep enough for Highland Park soil. Once a post moves, every part attached to it wears faster: hinges, latch, opener arm. Installing a new gate means new posts, set to carry the load for decades.
- Rust has eaten through the bottom rail or the hinge tabs. Highland Park’s humidity and rain find every seam. When rust goes through the section, not just on top of it, welding patches buys months, not years. Replacement is usually the honest fix and cheaper than a falling leaf landing on a car.
- The gate doesn’t match the house or the fence anymore. A gate that looks like an afterthought drags down the curb appeal of the whole front of the property. If the fence is iron, the gate should be too, and it should look like it belongs there, not like a homeowner special from two owners ago.
- You’re pouring money into repairs every year. If the same hinge, the same wheel, or the same motor mount fails more than once every couple of years, the old gate is worn past the point of honest repair. A new installation stops the cycle, and it’s protected by our written 90-Day Done Right Promise.
Our Gate Installation Process - Step by Step
- 1
Free on-site measure and written quote. We come out, check the driveway width, slope, soil, and existing posts, and walk you through the options in steel, iron, aluminum, or wood. You get a written price with the full scope of work, and nothing starts until you approve it. No deposit games, no vague allowances.
- 2
Design and material selection. We go over the gate style, picket spacing, height, and finish, including any matching to existing fence lines or architectural details on the house. If you want automation, we spec the opener for the gate’s weight and duty cycle right here so there’s no retrofit surprise later.
- 3
Fabrication and post setting. The gate is built in our shop to your dimensions, then the posts are set on site with concrete at the proper depth for the soil and the leaf weight. We let the concrete cure before hanging a gate, because hanging a half-ton leaf on green concrete is how posts start leaning in year two.
- 4
Hanging, welding, and automation. The gate goes up, the hinges get welded and aligned, and we dial in the latch, the stops, and the swing or slide travel. If there’s a motor, we mount it, run the wiring, and program the limits and safety edges so the gate opens and closes the way it should from the first cycle.
- 5
Final walkthrough and the Done Right Promise. We open and close the gate with you, show you how the manual release works, and hand you the written 90-Day Done Right Promise. If anything isn’t right within 90 days, we come back and make it right. No paperwork, no arguing, no exceptions.
How Much Does Gate Installation Cost in Highland Park?
A typical driveway gate installation in Highland Park runs $4,800 to $14,000, and where your project lands depends on the material, the driveway width, and whether automation is included. A basic single-leaf steel driveway gate without a motor might fall between $4,800 and $7,500. A double wrought iron driveway gate with automation and an intercom or keypad generally sits in the $8,000 to $14,000 range. Pedestrian gates are smaller, usually $1,800 to $4,500 depending on the material and whether you want them to match the main gate. These are Highland Park numbers, not Gate Installation in Dallas averages, and they reflect the cost of steel, the soil conditions, and the labor in this market.
| Installation Type | Typical Range | What It Includes |
|---|---|---|
| Pedestrian gate (steel or wood) | $1,800 - $4,500 | Gate, posts, hinges, latch, finish |
| Single-leaf driveway gate (no motor) | $4,800 - $7,500 | Gate, posts, concrete work, hinging, finish |
| Double driveway gate (no motor) | $7,000 - $11,000 | Two leaves, posts, cane bolt, hinges, finish |
| Double driveway gate with automation | $8,500 - $14,000 | Everything above plus opener, wiring, safety edges |
What affects the price more than anything is the gate’s weight and how far the posts have to go into the ground. Highland Park’s clay soil holds moisture and moves with the seasons, which is why we set posts deeper than a contractor working in rock or sand would. Automation adds $1,800 to $4,500 depending on the opener brand and whether it’s a swing or slide application. You avoid overpaying by getting a written line-item quote and comparing it against what’s actually being built, not just a photo. Our estimates are free, itemized, and the price we quote is the price we work to, agreed before a single bolt is turned.
Gate Installation Near Highland Park - Our Service Area
Our gate installation work covers Highland Park and reaches into Dallas, University Park, Lakewood, North Dallas, and the surrounding communities. We routinely work in Balch Springs, Mesquite, Oak Cliff, Farmers Branch, Addison, Irving, and Far North Dallas, and many of those jobs start with a call from a homeowner who heard about us from a neighbor. If you’re outside Highland Park, call any of our service area pages, including Gate Installation in Dallas and Gate Installation in Balch Springs, to see what applies to your neighborhood. We schedule measures within a few days in most of the metro area, and home is always a good place to start if you want the full scope of what we do.
Serving Highland Park, TX - Our Local Coverage Area
We’re based in the Highland Park area and also handle Gate Installation - Irving; we know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Installation in Highland Park
Gate installation is the full process of setting the gate posts, fabricating or fitting the gate leaf or leaves, hanging the gate, and aligning the hinges, latch, and any automation so it opens and closes cleanly. In Highland Park, that means considering the driveway grade, the clay soil, and the style of the house and fence. It’s not a handyman job with a post-hole digger: it’s structural work, and it’s what we’ve done since 1984.
Most residential gate installations in Highland Park take two to four days from the day we show up to the day we hand you the remote. That includes post setting, concrete curing time, hanging, and automation setup if you’re adding a motor. We’ll give you a straight answer on timing when we quote, and we show up when we say.
A driveway gate in Highland Park typically runs $4,800 to $14,000 installed, and pedestrian gates run $1,800 to $4,500. The range depends on material, width, and automation. Call (936) 277-6521 for an exact written quote; the estimate is free and there’s no obligation.
Yes, we install and service all five of those brands, along with FAAC, DoorKing, Elite, and Mighty Mule. If you already have an opener on the property, we’ll integrate it with the new gate or replace it with a correctly sized unit. Bring us whatever brand is on the driveway, and we’ll know what to do with it.
We can usually send a technician for a measure within a few days anywhere in Highland Park or the nearby neighborhoods. For a broken gate that’s a safety concern, we offer Emergency Gate Installation in Highland Park, TX and we’ll work to get someone out the same day. Call (936) 277-6521 and a live person answers, 24 hours a day, 7 days a week.
Every gate installation we complete in Highland Park is covered by our written 90-Day Done Right Promise. If anything isn’t right within 90 days, we come back and make it right at no charge. No paperwork, no arguing, no fine print.
Clear the driveway area so we have room to work and to set the posts, and move any cars off the apron on install days. If you have a sprinkler system near the gate line, mark the heads so we can avoid them when we dig. We’ll handle the rest, including a walkthrough before we start and another after the final cycle.
Schedule Your Gate Installation Service in Highland Park Today
If your gate is sagging, scraping, or simply not the gate this house deserves, call Ironworks Gate Co. at (936) 277-6521. We’ll schedule a free measure, write the quote, and give you a straight answer on cost and timing. A live person answers 24 hours a day, every day. The job gets done right, and it’s backed in writing.
Written by Victor Salinas, Owner of Ironworks Gate Co., serving Highland Park since 1984.