Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Garland
Gate parts and welding in Garland usually means one of three things: a hinge post that has shifted in the clay, a roller that has worn flat on one side, or a weld that finally let go after years of Texas sun and soil movement. We fix all three, and we do it with a written 90-Day Done Right Promise behind every job. If your gate scrapes the driveway, binds against the rail, or hangs off-square, call us at (936) 277-6521 and we’ll send a background-checked, uniformed technician to your Garland home. Most repairs are completed in a single visit, with the price settled before a single bolt is turned.
Why Ironworks Gate Co. Is Garland’s Preferred Gate Parts & Welding Company
We’ve been at this trade for more than 42 years, founded in 1984, and the work we do in Garland is the same work we’d do on our own mothers’ houses. That’s not a slogan. It’s the K.E.Y.S. values code every technician carries: Krafted right, Every time, Your home first, Standing behind it. The 400th job gets the same care as the first. Homeowners in Garland call us because they’ve had a generalist handyman out before, someone who tightened a hinge and left, and six months later the gate sagged again. The difference is that we understand what’s happening under the post, not just on top of it.
We dispatch from our Dallas-Fort Worth office and keep crews serving Garland locally, so response times are short and the technicians know the neighborhoods: Firewheel, Duck Creek, Bradfield, Broadway, and the older post-war belt near downtown. That local knowledge matters when a gate fails, because the fix on an Eagle Ridge home with a west-facing iron fence is different from the fix on a 1970s ranch off Saturn Road. We see it every week.
Our Gate Parts & Welding Services in Garland
Hinge Replacement
Hinges on Garland swing gates carry more than the weight of the gate. They carry the movement of the soil underneath the post. When the clay expands after a wet spring, the post shifts and the hinge takes a twisting load it was never designed for. We replace worn, seized, or snapped hinges with properly sized weld-on or bolt-on hardware, and we check the post footing at the same time. A new hinge on a shifting post is a temporary fix. We’d rather do it once.
Post Replacement
This is the big one in Garland. The subdivision boom west of Lake Ray Hubbard and the older belt near downtown both sit on expansive clay soil that swells and shrinks through the year. A hinge post set in that soil will heave, lean, or rotate over a single wet-dry cycle, leaving the gate scraping the concrete or binding the operator. We cut out the old post, pour a new 24-inch Sonotube footing below grade, and set the post true so the gate swings clean. It’s the difference between a repair that lasts a season and one that lasts decades.
Rail Repair
Slide gate rails in Garland take abuse from runoff sand and grit, especially on properties near Duck Creek or anywhere the driveway slopes toward the street. Rail repair usually means straightening a bent section, re-welding a cracked joint, or replacing a worn rail outright. We also check the rollers when we’re in there, because a flat-spotted roller is often what caused the rail damage in the first place.
Custom Welding
Some gates can’t be repaired with off-the-shelf parts. Older Garland homes often have gates built by a local fabricator twenty or thirty years ago, and those odd sizes and custom picket patterns need a welder who can match the original work. We do custom welding for brackets, stiffeners, decorative repairs, and structural reinforcement. Victor Salinas leads the team, and if it’s steel or wrought iron, we can make it right.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Garland
We’re not brand-loyal in the way that limits a repair. We’re trained and equipped on nine gate-automation brands, including LiftMaster, FAAC, and Linear, which means whatever is mounted on your Garland driveway, we can diagnose it and fix it correctly on the first visit. We also keep common replacement parts stocked for Garland customers: rollers, hinges, brackets, capacitors, and control board components. That keeps a one-visit repair from becoming a two-week parts wait. Our Gate Parts & Welding team handles everything from the hinge to the motor.
Common Gate Parts & Welding Problems We See in Garland Homes
- Clay soil shifting hinge posts. Garland’s expansive clay swells in wet seasons and shrinks in dry heat. A post set in that soil will move, and the gate will start scraping the driveway or binding the operator. Sag correction here almost always requires re-footing the post, not just tightening hardware.
- Slide gate rollers wearing flat from runoff sand. Homes near Duck Creek and anywhere with a sloped driveway see grit washing across the gate rail. That grit grinds rollers unevenly, and the gate starts to bind against the rail instead of gliding.
- Solar opener batteries swelling in west-facing fences. Garland summers are brutal, and a solar panel on a west-facing fence will bake the battery. Swollen cells can mimic a failed loop detector, with the keypad working but the gate refusing to move.
- Weld fatigue on older custom gates. Gates built in the 1980s and 1990s were often welded with thinner stock than we’d use today. After thirty-plus years of heat, rain, and gate cycles, those welds crack. We re-weld them with proper penetration and add gussets where the original fabricator skipped them.
Pricing for Gate Parts & Welding in Garland, TX
A hinge replacement on a Garland swing gate typically runs $180 to $340, including parts and labor. Post replacement is the bigger job: $450 to $900 depending on whether we’re re-footing one post or both, and whether the operator needs to be dismounted and re timed afterward. Rail repair runs $200 to $550 depending on length and damage. Custom welding is quoted per job, but most small structural welds land between $150 and $400. Rollers: $120 to $260 per set, installed. Every quote is written and agreed before work starts, so the invoice matches the number you approved. We also offer $50 off any repair over $250, a free second opinion on any written estimate, and a permanent 5% senior and veteran discount. Call (936) 277-6521 for an exact price on your gate.
We Also Serve Cities Near Garland
Our crews work throughout the northeast Dallas-Fort Worth metro. We serve Gate Parts & Welding in Garland and the surrounding communities including Richardson, Mesquite, Addison, and Dallas. Same team, same 90-Day Done Right Promise, same upfront pricing.
Serving Garland, TX - Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Garland
The gate isn’t sagging. The post underneath it is moving. Garland sits on expansive clay soil that swells when spring rains soak in and shrinks when the summer heat bakes it dry. A hinge post set in that soil will heave and lean over a single season, and no amount of hinge tightening will fix it. The post needs to be re-footed: we cut it out, pour a new 24-inch Sonotube footing below the frost and expansion zone, and re-set the post plumb. Then the gate hangs true and stays true. Call (936) 277-6521 for a post inspection at your Garland home.
We can, but we’ll tell you honestly whether you should. A new operator on rollers with flat spots or worn bearings will bind under load and burn out the motor faster. If your rollers are round and rolling freely, we’ll keep them. If they’re worn, we’ll show you the wear marks and quote a replacement. New rollers installed with the operator usually runs $120 to $260 on top of the operator cost.
Yes. Photo-eyes are a required safety device on any automatic gate, and we test them on every installation and service call in Garland. A gate that reverses only on contact has already hit whatever it’s reversing against - a child, a pet, a car. The photocell stops the gate before contact. We install and align them as part of every operator job, no exceptions.
It could be, and it’s one of the first things we check. A failed loop detector will make the operator think a vehicle is always present, which blocks the gate from opening. But the same symptom shows up from a swollen solar battery on a west-facing Garland fence, a bad limit switch, or a disconnected safety edge. We diagnose it in one visit, whatever brand you have. Call (936) 277-6521 and we’ll get a technician out to your Garland driveway.
No. If you have AC power at the fence, run the gate on AC. Solar is for fences where running power isn’t practical. Garland’s summer heat shortens solar battery life, especially on west-facing installations, and a swollen battery can strand your gate closed on the hottest day of the year. AC power means one less failure point and fewer service calls over the life of the operator. We’ll wire it properly and in conduit, with the safety edges and photocells tested before we leave.
Need a gate fixed in Garland? Call Ironworks Gate Co. at (936) 277-6521 for a free estimate. A live person answers 24 hours a day, 7 days a week. We’ll quote the work upfront and stand behind it with our written 90-Day Done Right Promise. No voicemail trees. No surprises on the bill. Just a gate that works.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving the Dallas-Fort Worth metro since 1984.