Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Irving
Gate access control in Irving, TX means getting the right equipment on your gate and knowing it will open when you punch the code, tap the remote, or answer the intercom. Most Irving jobs we complete in a single visit, with a keypad or card reader replacement typically running $240 to $420 installed, and a full video intercom retrofit starting around $950. Whether your home sits off Belt Line Road or in a gated section of Valley Ranch, we coordinate scheduling from our Dallas-Fort Worth office and keep a live person on the phone 24 hours a day. Call (936) 277-6521 and you’ll get an answer, not a recording.
Why Ironworks Gate Co. Is Irving’s Preferred Gate Access Control Company
We’ve been doing gate work since 1984, and the Irving homeowners we serve tend to have lived in their houses for twenty years or longer. They remember the last contractor who didn’t show or left a bill that didn’t match the quote. That’s exactly why we put every job in writing upfront: the price you approve is the price you pay, settled before our technician turns a single bolt. Our Gate Access Control work in Irving carries the same 90-Day Done Right Promise as every other job we do. If something isn’t right, we come back and make it right. No paperwork, no arguing.
Victor Salinas leads our team, and he’s built the company on a simple standard: treat every Irving home the way you’d treat your own mother’s house. That means background-checked, uniformed technicians, a live person answering every call, and no pressure to replace something that could be repaired honestly. We’re certified on nine automation brands, including LiftMaster, FAAC, and Viking, so the fix we make on your first visit is usually the only fix you’ll need.
Our Gate Access Control Services in Irving
Keypad Entry
A new keypad entry system for an Irving driveway gate typically runs $240 to $420 installed. On older homes in Heritage District and University Hills, the first thing we check is the condition of the keypad membrane itself. West-facing brick columns in Irving take direct afternoon sun, and those rubber membranes crack at the hinge after a few Texas summers. A cracked membrane lets moisture reach the contacts, and that’s when codes stop working. We replace the keypad, seal it against weather, and program it on the spot.
Remote Control
If your gate remote works only from ten feet away or stops responding altogether, the problem is usually the receiver board or the antenna, not the remote itself. In Irving, we see receiver boards corroding from humidity cycles that swing hard between the wet spring months and the dry heat of July and August. A receiver replacement on most residential gates runs $180 to $300. We program every remote in your household while we’re there, including the one in the glovebox of the car that’s been dead for two years.
Phone Entry
Phone entry systems let you open your gate from the same cell signal you use for everything else. On Irving properties with detached garages or long drives off MacArthur Boulevard, phone entry is often the cleanest upgrade because there’s no wiring to trench back to the house. A cellular-based gate controller installed runs $450 to $650. You add the phone numbers of everyone in the household, and the system rings them in order when someone calls the gate line. We configure everything before we leave and walk you through how to add or remove a number.
Card Reader
Card readers make sense for Irving homes that see regular family traffic: kids coming home from MacArthur High, a caregiver arriving daily, housekeepers on schedule. A proximity card reader installed ranges $350 to $550, and we supply the cards configured to your system. For townhome communities in Las Colinas with shared gates, the board or HOA typically needs to approve changes, and we can help you prepare that request with a written quote and spec sheet.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Irving
We carry parts and replacement boards for the automation brands Irving homeowners actually have on their gates: LiftMaster, FAAC, Elite, Mighty Mule, and more. Because we stock these local, we’re not waiting on a distributor to ship when your relay or limit switch cooks out. Whether you’ve got a LiftMaster operator from 2008 or a newer FAAC unit, the technician who shows up already knows the wiring and the failure points. That matters on a repair visit, and it matters even more when we’re adding a keypad or a video intercom to a system built years ago.
Common Gate Access Control Problems We See in Irving Homes
- Loop detectors false-cycling in Las Colinas: Underground irrigation wiring crosses under many driveways in Las Colinas, and the electrical field it carries can interfere with a gate’s ground loop sensor. The gate reads a phantom vehicle, opens, then reopens when it should stay shut. We test the loop frequency and relocate or shield the loop when the interference is severe.
- Sun-baked keypad membranes in Heritage Crossing: A west-facing brick column in Heritage Crossing takes six to eight hours of direct sun in July. Rubber membranes crack at the digit hinges, moisture gets in, and the keypad shorts. We replace the membrane, and when the column is going to keep baking, we recommend a metal-shrouded keypad that won’t cook in the same way.
- Sagging swing gates on older posts: Many 1970s-era Irving homes have swing gates hanging on posts that were set no more than 24 inches deep. The clay soil expands and contracts through wet-dry cycles, the post leans, and the gate’s rack-and-pinion mesh wears unevenly until it binds or strips. We reset the post to a 36-inch depth on new footings and re-hang the gate square.
- Unpermitted operator replacements from past years: In Irving, automatic gate openers require secondary entrapment protection and annual safety inspections. But plenty of older homes in Valley Ranch and Heritage Crossing got operator swaps years ago that were never permitted and never had safety photocells installed. Our access-control retrofits expose these routinely. We bring the system to current code, file the permit paperwork, and test it before we leave.
Pricing for Gate Access Control in Irving, TX
Here are honest numbers for the Irving market. A keypad replacement runs $240 to $420. A receiver board repair for a remote control system runs $180 to $300. A phone entry system starts at $450 and typically lands under $650. A single-card proximity reader is $350 to $550. A video intercom retrofit starts around $950 and runs higher when we’re trenching new cable from the house to the gate. The main factors that move the price are trenching distance, the condition of the existing operator, and whether the post needs to be reset. Every price is quoted and agreed before any work starts, in writing. Call (936) 277-6521 for a free estimate, and remember our standing offers: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount.
We Also Serve Cities Near Irving
Ironworks Gate Co. serves homeowners throughout the Dallas-Fort Worth area from our metro office, and we regularly work in Irving as well as Dallas, Addison, Carrollton, and Richardson. If you’re on the edge of town or your gate sits in a pocket between city boundaries, call us and we’ll tell you straight whether we can get a technician to you. The answer is almost always yes.
Serving Irving, TX - Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Irving
Yes. Irving’s municipal code requires a permit for automatic gate operator replacements on residential properties, and any opener installed after the current code was adopted must have a secondary entrapment-protection device, typically a monitored photo eye or contact edge. We handle the permit paperwork as part of the job. The keypad itself doesn’t trigger a separate permit, but if we’re pulling new low-voltage wire from the house, that run should be on the same permit as the operator work. Call (936) 277-6521 and we’ll check what your specific property needs before we start.
Yes, in most cases. A video intercom can be added to an existing swing gate operator as long as the operator’s control board has an accessible open-command input, which most LiftMaster and FAAC boards from the last 15 years do. The intercom handles the call, the video, and the unlock signal; the operator still does the physical opening. On Irving homes where the driveway is more than 60 feet from the house, we run shielded Cat6 cable rather than relying on Wi-Fi, because two stucco walls and a brick column will kill a wireless signal before it ever reaches the gate.
For an automatic gate, the post footing should be at least 36 inches deep and 18 to 24 inches in diameter, set below the frost line and keyed into undisturbed clay. Irving’s blackland prairie clay expands and contracts dramatically through wet-dry cycles, and a shallow post will lean within two or three years. When we replaced a failed LiftMaster slide gate operator for a homeowner in Valley Ranch, the original footing had been poured shallow and shifted, and the rack and pinion had stripped as a result. We poured a new 36-inch-deep footing, installed a Viking operator with a UL 325 monitored retro-reflective photo eye, and tested reversal force with an edge sensor before sign-off. That’s the standard we apply to every gate we touch in Irving.
That’s almost always loop detector interference. The ground loop embedded in your driveway generates a field that tells the operator when a vehicle is present, but underground irrigation wiring running alongside it can induce enough current to trigger a false reading. The gate thinks there’s a car in the path, so it reverses. We diagnose this with a loop tester on the detector’s frequency, and when the irrigation run is the culprit, we relocate the loop or shield the wiring so the gate only reacts to an actual vehicle. In Las Colinas we’ve seen this enough times that we check loop interference early in the diagnosis. Call (936) 277-6521 and we’ll get a technician out to check it.
Irving code requires a secondary entrapment-protection device on every automatic gate opener, which means a monitored photo eye or contact edge in addition to the operator’s built-in force-sensing. Annual safety inspections are also required. We test the reversal force with a pressure gauge, confirm the photo eye alignment, and document the results so you have a paper trail if you ever sell the home. If your gate predates the current code, we’ll tell you exactly what’s missing and what it costs to bring it right. The test itself is included with our $89 seasonal tune-up.
Call Ironworks Gate Co. for Gate Access Control in Irving
If you’re in Irving and your keypad won’t accept codes, your remote only works at arm’s length, or you just want a gate that opens every time without a second thought, call us at (936) 277-6521. A live person answers, 24 hours a day. We’ll give you an honest quote before any work starts, and every job is backed by our 90-Day Done Right Promise in writing. Victor and the whole Ironworks team would rather spend forty minutes on the phone helping you understand the problem than sell you something you don’t need. That’s how we’ve worked since 1984.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Irving and the Dallas-Fort Worth area since 1984.