Linear Gate Installation Nationwide

Linear Gate Installation in Highland Park: What to Know First

Linear gate installation in Highland Park typically runs $850 to $3,200 depending on the gate’s size, whether it’s a swing or slide design, and the opener model already on the property or going in new. Most standalone Linear opener installations are completed in a single day, and we quote the full job before any work begins so the number on the invoice matches the number you approved. If you own a Linear operator that’s failed or you’re building a new driveway gate and want Linear automation, this page covers what actually happens on those jobs in Highland Park, from the first call to the final test. Call (936) 277-6521 and a live person answers, day or night.

Call (936) 277-6521

How Linear Products Fail - and How We Fix Them

Linear operators are common on Highland Park estate gates because they were a go-to brand for builders in the 1990s and early 2000s. The ones still running today have usually been through a few repairs. Here’s what we see most on Linear jobs and how we handle each one.

• Linear LRA and LD series swing arm failures: The older Linear LRA swing gate operators use a worm-gear drive that wears out after years of pushing heavy iron gates. When the gear strips, the gate won’t hold position and you’ll hear the motor run while the gate barely moves. We replace the gear assembly with OEM parts when available, or a machined aftermarket equivalent that matches the factory spec. The fix typically holds for another decade or more.
• Linear APeX and MegaCode receiver drift: Linear’s APeX series and MegaCode receivers sometimes stop responding to remotes after storms or nearby lightning. The code memory isn’t damaged, but the receiver board loses its programming. We re-sync the receiver, replace the backup capacitor if it’s swollen, and set the remotes back up before we leave. No service call for “the remote stopped working” is closed until every remote and keypad is tested at the gate.
• Limit switch failures on Linear slide operators: The SL and SLR series slide gate operators use mechanical limit switches that get bumped out of adjustment when a gate hits an obstruction or a concrete driveway shifts. The gate then stops short or overruns its track. We set the limits, adjust the torque limiter so the gate stops if it meets real resistance, and verify the safety edges work. A slide gate that overruns is a genuine safety hazard, and this repair is one we always recommend handling immediately.
• Capacitor death on M80 and LA500 series: Linear’s M80 and LA500 arm operators use a large start capacitor. In a Highland Park summer attic or unshaded gate box, that capacitor cooks. The gate hums but won’t start, or opens halfway and stalls. We replace the capacitor with a high-temperature-rated unit and check the control board for heat damage while we’re inside the box. It’s a $60 part and ten minutes of work, but the diagnosis matters because a bad capacitor can take out the board if ignored.
• Chain tension problems on Linear SL slide operators: The SL series uses a chain drive that stretches over time. A loose chain causes jerky motion and premature sprocket wear. We set proper chain tension, align the drive sprocket, and lubricate with a dry film lubricant that doesn’t attract the dust we get in North Texas. The gate should roll smooth, not lurch.

One thing we tell every Linear owner: these operators were built to be serviced. The boards, the caps, the gears, the limit switches all come apart and go back together. When a unit is beyond saving, we tell you straight rather than selling parts into a losing fight, and we’re quoting a replacement before we leave the driveway.

Our Linear Gate Installation Process

Here’s how a typical Linear gate installation goes at an Ironworks job in Highland Park, from the first ring to the final walk-through.

1. 1
   Call and diagnosis: You call (936) 277-6521, a live person answers, and we schedule a visit. Victor Salinas himself or one of our senior techs comes out, listens to what the gate is doing, and opens the panel to confirm the diagnosis.
2. 2
   Parts decision: If the operator needs parts, we show you what failed and lay out the OEM versus quality aftermarket options. On Linear units, OEM boards are usually the right call for electronics; for mechanical components like gears and caps, a specification-matched aftermarket part often does the job for less. You decide, and the price is set before we order anything.
3. 3
   The install: We remove the old operator, prep the mount and post, and install the new unit or parts. For full installations, this includes setting the gate’s travel, installing or checking the safety edges, and making sure the gate opens and closes with proper force limits.
4. 4
   Programming and test: Every Linear remote, keypad, and the receiver get programmed and tested. We run the gate through at least a dozen full cycles, check the auto-close timing, and stand at the gate while it opens and closes, listening for anything that sounds off.
5. 5
   Cleanup and walk-through: We leave the work area cleaner than we found it, then walk you through what we did and why. You’ll know what to expect from the gate, how the remotes work, and what the warranty covers.
6. 6
   Written guarantee: Every job gets our 90-Day Done Right Promise in writing. If something isn’t right, we come back and make it right. No paperwork, no arguing.

What Linear Gate Installation Costs in Highland Park

Linear gate installation costs in Highland Park fall into predictable ranges, and we quote the job before a single bolt is turned. Here’s what you should expect as an independent Linear service provider, not a manufacturer-authorized shop, which means our pricing reflects what the work actually costs rather than what a corporate schedule says it should.

• Standalone Linear opener installation (labor only): $350 to $750, depending on the mount and any post work needed
• Linear SL slide operator installed on an existing gate: $900 to $1,800
• Linear LRA swing arm operator installed on an existing single gate: $850 to $1,500
• Full double gate installation with Linear automation: $2,200 to $3,200, including both operators, safety edges, and programming
• Capacitor or limit switch replacement on an existing Linear unit: $140 to $260

What moves the price: gate weight, post condition, whether the electrical is already at the post, and whether we’re doing a straight replacement or a first-time automation. We give you the number before work starts, and that’s the number on the invoice. Call (936) 277-6521 for a free estimate on your exact setup.

Why Highland Park Homeowners Call Ironworks Gate Co. for Linear Work

We’ve been doing this for over 42 years, since 1984, and Linear operators have been on Highland Park driveways for most of that time. Victor Salinas grew up near Turtle Creek, where the older estate ironwork caught his eye long before he knew what to call the craft. He’s been the name homeowners call when a gate won’t move for well over two decades. When you call us about a Linear gate, the tech who shows up knows that board, that motor, and that receiver. And if the job ever calls for a different solution, we service eight other opener brands too: LiftMaster, Mighty Mule, Ghost Controls, DoorKing, FAAC, BFT, Viking, and Elite. Every job is protected by our written 90-Day Done Right Promise. Most Linear installations are done in a single visit, and we never leave a gate that doesn’t open and close exactly as it should.

FAQs