Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The Highland Park Owner’s Guide

Most Ghost Controls keypad and intercom failures in Highland Park come down to two things: weather getting past a worn seal, or a control board that’s been asked to work past its lifespan. We stock Ghost Controls-compatible keypads and intercom components on the truck, and typical installed repair pricing runs $240 to $480 depending on the model and what failed. Most keypad swaps happen in a single visit, often the same day you call.

Call (936) 277-6521

Here’s how it usually plays out. You’ve had your Ghost Controls opener running faithfully for years. Then one morning the keypad beeps but won’t release the gate, or the code gets finicky, or the intercom at the drive just goes quiet. You get out, punch in the code again, maybe change the battery in the keypad, and it works for a day. Then it doesn’t. The part has failed, and no amount of button-mashing brings it back. We’ve seen this exact pattern hundreds of times across Highland Park driveways, and the fix is usually more straightforward than homeowners expect when the right part is matched to the right opener on the first try.

Ironworks Gate Co. is an independent gate repair company. We are not affiliated with Ghost Controls. What that means for you is plain: we’re not tied to one parts pipeline, so we can recommend the part that actually suits your gate, not just whatever is on the shelf.

Which Ghost Controls Models This Applies To

Ghost Controls sells keypads and intercom units across several series lines, and not every part fits every board. The two keypads we replace most often in Highland Park are the AXDP and AXS1 models, plus the wireless keypad that ships with many Ghost Controls single-gate kits sold through the big box stores. Each one talks to the control board differently: some use a radio receiver paired to the board, some hardwire into the terminal strip, some run through an intercom relay. Getting this wrong means a keypad that technically “works” but won’t trip the relay, which is why compatibility has to be checked against the board, not just the brand name.

If your opener is a Ghost Controls TSS1, TDS2, or the older Ghost Pro line, write down the model number from the control board before you call anyone. That number, plus the label on the back of the keypad, is what lets us match the right piece the first time. When it comes to OEM versus aftermarket, our honest take after over 42 years in this trade: Ghost Controls branded parts are solid, and aftermarket keypads from quality manufacturers like LiftMaster and DoorKing can sometimes outlast the originals, particularly in Texas heat. We’ll lay out both options with straight numbers, then you decide.

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

Here are the patterns we see consistently on service calls in Highland Park:

• The code works, but only sometimes. This usually means the keypad’s internal membrane is wearing out, or moisture has found its way past the seal and is bridging contacts intermittently. It is not the opener. The signal counts should be a clue.
• The keypad beeps and flashes, but the gate doesn’t move. The keypad is fine. The receiver on the control board has stopped recognizing it, or the relay wire to the opener has corroded or come loose at the board terminal.
• You hear static or nothing from the intercom at the drive. Often it’s the speaker cone, which fails in humid conditions. We see this a lot in the spring after heavy rain, particularly on estates with older landscaping that keeps the intercom in shade where it never dries out.
• Certain buttons stopped responding. Each key is a switch. When one or two go dead, the membrane underneath has failed at those points. The rest of the keypad may last a year, but the end is coming.
• The keypad corroded or filled with water after a storm. Ghost Controls keypads are sealed, but the seal doesn’t last forever under Texas sun. We see UV embrittlement starting around year five or six. The plastic just gives up.

If any of this sounds familiar, we’d rather you know early. A failing keypad tends to fail completely at the worst moment, and a gate that won’t open when you’re coming home in the dark is not something we want anyone dealing with.

Replacement Cost & What’s Included

For Highland Park, installed Ghost Controls keypad replacement typically runs $240 to $380. Intercom repair or replacement runs closer to $320 to $480 installed, depending on whether we’re rebuilding the handset, replacing the speaker, or swapping the whole unit. Every quote is broken down so you can see parts and labor separately. We tell you the price before we touch a bolt, and the price you agree to is the price you pay. No surprises on the bill, ever.

What’s included in our repair work: the correct Ghost Controls-compatible part, the install, the programming and pairing to your existing board, and testing of the full open-and-close cycle before we leave. We also check the gate’s limit settings and safety edges while we’re there, because if the board’s out of adjustment, a new keypad just masks a deeper problem. Every part and every hour of labor is backed by our written 90-Day Done Right Promise.

For homeowners holding a written estimate from another company, ask about our Free Second Opinion. We’ll look at the same symptoms, the same part, and the same numbers, and tell you the truth either way.

DIY or Call Us?

We are never going to tell a homeowner they can’t check a few things themselves. Look at the keypad: is there water inside the lens, is the case cracked, are the terminals at the board tight? If it’s a battery-powered keypad, try a fresh battery. That fixes a surprising number of calls, and we’ll happily say so.

Where DIY goes sideways is the programming and wiring. Ghost Controls boards have small terminal strips, and the difference between the relay input, the 12V out, and the safety-loop terminals is measured in millimeters. One wrong wire to the wrong terminal can fry the board or burn out the transformer, and that is a $350-plus mistake on a job that would have been $280. Keypads and intercoms are low voltage, so the danger is mostly to the board, not to you. But from a safety standpoint, if your gate is hardwired to high voltage, or if you’re ever opening the control box and see anything you don’t understand, step back and call us at (936) 277-6521.

FAQs